Executive Summary - Specification and Supply Position
TL;DR - The Mistairhome WL-QH01S (PRO) holds 420 mL and mists 40 mL per hour or 19.0 mL per hour, which is 10.5 hours and 22.1 hours per fill; it covers 11 sq m (113 sq ft) at a 2.6 m ceiling and measures 25.8 dB on the high step and 23.2 dB on the sleep step; it draws 2.7 W and runs from USB-C 5V/1A, runs from a laptop port or a phone charger; no internal cell on this build; it weighs 404 g and measures 10.4 x 10.4 x 18.6 cm, and ships documented to CE / RoHS / FCC standards for import into Colombia. MOQ is 200 units per SKU with a 20-30-day lead time, FOB Shenzhen or EXW Longgang.
China Wanlin supplies the Ultra Quiet Bedroom Humidifier category as a direct manufacturer, not as a trading intermediary. The unit described below is one configuration out of 24 combinations (8 chassis x 3 SKU builds) that share a common misting family, a common tank and seal line and a common documentation set, so a distributor can build a coherent shelf from one source rather than stitching together unrelated suppliers. Every unit referenced on this page corresponds to a specific bill of materials held on file, so the figures below can be reproduced or independently verified at sample stage.
Full specification of WL-QH01S-PRO:
| Misting method | Ultrasonic piezo disc at 1.7 MHz on a floating silicone isolator, cool mist, no heater in the path |
| Tank capacity | 420 mL |
| Mist output on the high step | 40 mL per hour |
| Mist output on the low step | 19.0 mL per hour |
| Run time per fill on the high step | 10.5 hours |
| Run time per fill on the low step | 22.1 hours |
| Coverage area | 11 sq m (113 sq ft) at a 2.6 m ceiling |
| Noise at 1 m on the high step | 25.8 dB |
| Noise at 1 m on the sleep step | 23.2 dB |
| Water type | Tap water or distilled; a demineralisation cartridge drops into the tank neck |
| Mineral dust handling | Cartridge optional, recommended wherever the supply is hard |
| Fill method | Wide top opening, filled in place from a jug |
| Battery pack | Not fitted, runs from the USB-C supply |
| Cordless run time | Not applicable, mains or USB powered |
| Charge time | Not applicable, no internal cell |
| Power input | USB-C 5V/1A, runs from a laptop port or a phone charger |
| Rated power on the high step | 2.7 W |
| Control interface | Touch strip with three mist steps, sleep mode and a two, four or eight hour timer |
| Night light | Amber ring below 4 lux, dimmable to fully dark |
| Protection | Dry-run shut-off by tank float, tilt switch, overcurrent limit on the adapter |
| Dimensions | 10.4 x 10.4 x 18.6 cm |
| Weight | 404 g |
| Warranty | 12 months |
Shipping configuration: Pro build, + spare misting disc + demineralisation cartridge + multilingual manual. Master carton holds 48 units. Stated lead time is 20-30 days from order confirmation and deposit. Misting discs, wicks and cartridges are repeat line items and are ordered separately from the appliance.
Why Buyers Are Sourcing This Category Now
The strongest pull in Colombia now comes from hospitality, clinical and facilities buyers rather than households, because they can put a number on complaints and on room-turn time, which makes the decision easy to defend internally. Two routes dominate access. The traditional route is importer to distributor to retail; the faster one is the cross-border seller who buys direct, preps for the marketplace and skips two margin layers.
Returns in the Ultra Quiet Bedroom Humidifier category cluster around three causes: mineral dust on hard water, units audible at night, and units sized to a floor area in a room with a much higher ceiling. All three are answered at quotation stage rather than after arrival. This is why the table above states figures by model rather than by marketing tier: a buyer comparing two SKUs needs the noise on the sleep step, the run time per fill and the water handling side by side, because those three predict both satisfaction and return rates better than any other set.
Wanlin serves Colombia through three programmes that suit different balance sheets. New partners start with sample evaluation then a mixed trial order. Established distributors move to scheduled container shipments with locked pricing windows. Brand owners run private-label programmes with their own artwork and manuals. In all three cases the factory documentation, including the certificates and battery files listed further down this page, references the specific model code on the order rather than a generic family certificate, which is the most common cause of customs delay in this category. On the WL-QH01S (PRO) the figures worth carrying into the next order are the 420 mL tank, the 22.1 hours per fill on the low step, and the 23.2 dB reading on the sleep step.
Engineering Notes - Noise, Mist Output and Water Quality
The decision that matters most in this category is not output, it is what the unit does with dissolved minerals, and it is the one most often sold badly. An ultrasonic disc atomises water, and with it everything dissolved in that water, so on a hard supply the minerals become airborne and settle as a fine white film on whatever is nearby. Two answers exist and we build both: a demineralisation cartridge in the tank, which is a consumable with a real working life, or an evaporative wick where the water never becomes airborne at all and the minerals stay behind in the wick.
The second decision is the control loop. A fixed mist step ignores the room entirely, so a sealed room overshoots while a draughty one never arrives. A humidistat with a stated target band, fed by a sensor that is calibrated at the factory and re-checkable by the buyer with a twenty-dollar hygrometer, is the difference between a product that holds a number and one that merely runs.
The third is the cleaning path, which is an engineering decision long before it is a marketing one. Standing water at room temperature grows biofilm, so the honest interval is every five to seven days in continuous use, and a tank a hand cannot reach into is a tank that never gets cleaned properly. For this configuration that means 19.0 mL per hour at 23.2 dB, holding 22.1 hours per fill across a 11 sq m (113 sq ft) room.
Featured Deployment and Field Case Records
Three deployment records from the Ultra Quiet Bedroom Humidifier programme, each with the conditions that shaped it. Site detail is kept because it is the part that transfers: the water, the ceiling, the rota and the complaint are what decide whether a unit stays in service, and none of them appear on a specification sheet.
Case Study 1: Leeds, United Kingdom
Deployment: A maternity hospital refurbishing 26 post-natal rooms
Timing: Six months from May 2025
Infection control reviewed everything before procurement would sign, and asked two questions suppliers rarely prepare for: how the tank is cleaned, and how often. A tank a hand cannot reach into is a tank that never gets cleaned properly, so the wide-opening models passed and the narrow-neck ones were eliminated on a hygiene ground rather than a performance one. The cleaning interval went into the ward's own maintenance schedule.
Case Study 2: Braga, Portugal
Deployment: A hotel school running 30 training bedrooms occupied by rotating students
Timing: One academic year from October 2025
Training bedrooms are harder on appliances than guest rooms because the occupants change weekly and read no instructions. What survived was the simplest chassis: one button, two steps, auto shut-off, and a tank that can be carried in one hand without spilling. The school's maintenance log for the year shows no units retired for damage, which is the outcome they measure.
Case Study 3: Da Nang, Vietnam
Deployment: A hospital supply distributor covering central Vietnam
Timing: Sixteen months from May 2025
The distributor serves both hospital and retail channels, and the documentation requirements differ between them. Certificates issued per model code rather than per family let the same container serve both channels without a second test round, which is a practical advantage that shows up in the landed cost rather than in the unit price.
The pattern across all three is that the deciding factor was never peak output. It was whether the tank lasted a full shift, whether the unit could be cleaned inside the time a round allows, and whether anyone complained about the noise or the dust. Those are the questions we ask before quoting. The WL-QH01S (PRO) packs 48 units to a carton, carries a 12 months warranty and a 20-30 days stated lead time, and draws 2.7 W on the high step.
Application Scenarios Across Bedrooms, Offices and Wards
Four placement patterns cover most of the enquiries we see for this category. The useful observation is that each one is answered by configuration and placement rather than by buying a larger unit, which is the default reflex and usually the wrong one.
| Scenario | Room or site | What the site needs | What the unit does |
| SC10-LARGESPACE | Open-plan rooms, studios and lobbies with ceilings well above 2.6 m | A floor-area figure quietly assumes a standard ceiling, and a heritage or lobby space rarely has one. | Sizing against the room volume instead, and where the space opens to the outside, closed-loop control holding a target rather than a fixed mist step. |
| SC03-WORKSTATION | Individual desks on an open-plan floor served by mechanical ventilation | A corridor or ceiling-mounted unit cannot reach a desk when the supply diffuser is moving air. | One compact unit per desk cluster sits inside the two-metre radius where the plume is still airborne, which is a placement answer rather than an output answer. |
| SC06-CLEANING | Sites where one person cleans twenty rooms on a timed round | Anything that has to be carried to a sink inverted, or scrubbed through a narrow neck, adds minutes to every room turned that day. | Top fill from a jug and a tank opening a hand can reach into, which is why housekeeping accepts this chassis and rejects narrow-neck designs on sight. |
| SC09-TANKRUN | Rooms with nobody responsible for refilling, and buildings on a weekly maintenance round | Refilling decides whether an appliance survives in a managed building more than performance does. | A large tank holding a night plus a working day on the low step, with a humidistat so the unit runs only when the room actually needs it. |
Two of these four are decided before the unit is switched on: whether the tank lasts the interval the site can actually service, and whether the cleaning task fits the round. For this configuration that means 19.0 mL per hour at 23.2 dB, holding 22.1 hours per fill across a 11 sq m (113 sq ft) room.
What a Factory-Direct Programme Changes for the Buyer
Three costs dominate ownership of this product and only one of them is on the invoice. The first is the appliance. The second is the consumable - cartridges, wicks and replacement discs - which is where the repeat revenue sits for every distributor we work with and which should be planned as a line item rather than bought occasionally. The third is staff time, because a tank that cannot be cleaned quickly is a tank that does not get cleaned.
A factory programme attacks all three. Consumables ship in the same container as the appliances, which is the cheapest way to buy them. Cleaning intervals are published rather than left to guesswork, and the tank geometry is chosen so the published interval is actually achievable by one person on a round.
What we do not offer is the lowest unit price in the market. A cheaper unit in this category usually buys a narrower tank neck, a disc of unspecified origin and no spares path, and every one of those shows up later as a cost somewhere else. For this configuration that means 19.0 mL per hour at 23.2 dB, holding 22.1 hours per fill across a 11 sq m (113 sq ft) room.
Certification, Water Quality and Market Access
Compliance in this category splits into two burdens that buyers often treat as one. The first is electrical and appliance safety: the CE technical file, an EMC test report and the IEC 60335-1 household appliance safety report, which is the set that gets a unit onto a shelf in Europe. The second applies only where a cell is fitted: a UN38.3 test report with an IEC 62133 cell report and an MSDS, which is the set that gets a unit onto a vessel.
The failure mode is predictable. A buyer orders a cordless build, books the freight, and discovers at booking that the cell documentation has not been raised for that specific model code. The units sit, the season moves, and the cost is not the certificate - it is the delay. We raise the documentation against the model code on the order rather than against a family, which is the only version a customs officer will accept.
RoHS and REACH declarations cover materials, and where a buyer's own regulator asks about the water path, we supply a declaration covering every wetted part. Where a market needs a local approval, we issue against PSE, KC or RCM at the same time as the CE work rather than after it, because the test evidence largely overlaps and doing them together costs far less than doing them twice. On the WL-QH01S (PRO) the figures worth carrying into the next order are the 420 mL tank, the 22.1 hours per fill on the low step, and the 23.2 dB reading on the sleep step.
Unit Economics, Consumables and Order Sizing
The economics of this line are an annuity, not a one-off sale, and buyers who plan it that way outperform the ones who do not. The appliance is the entry; the cartridge, the wick and the replacement disc are the repeat, and in the pharmacy and hospitality channels the consumable revenue overtakes the appliance revenue within the first year.
Freight is the part that needs doing carefully. At 0.123 cubic metres per carton of 48 units, a 40 ft container carries roughly 18,192 units by volume, and a 20 ft about 8,256. Those are upper bounds before pallet and loading losses, and the honest planning figure is a little below them.
What we suggest to a first-time buyer is deliberately unglamorous: a mixed trial order across two or three SKUs, spares at one disc per twenty units, a stated lead time of 20-30 days written on the proforma invoice, and a re-order point set by sell-through rather than by calendar. On the WL-QH01S (PRO) the figures worth carrying into the next order are the 420 mL tank, the 22.1 hours per fill on the low step, and the 23.2 dB reading on the sleep step.
Buyer Questions Answered
What is the minimum order quantity for a first quiet humidifier order?
MOQ is 200 units per SKU for standard builds and 300 units for custom colour or private-label packaging. Mixed-container orders combining several models are accepted as long as each individual SKU clears its own minimum. The specification table on this page shows the exact build we ship for WL-QH01S-PRO.
How is the noise figure measured, and what does it mean in a bedroom?
We measure at one metre in a semi-anechoic corner and quote the step, so the two published figures for WL-QH01S are 25.8 dB on the high step and 23.2 dB on the sleep step. The sleep-step figure is the one to compare, because it is the step a bedroom unit is left on all night. A buyer can repeat the measurement in a quiet room with a phone application and will get within a decibel or two.
Does this humidifier leave white mineral dust on furniture?
It depends on the water and on the misting method, and it is the single largest cause of returns in this category. An ultrasonic disc throws everything dissolved in the water into the air, so on a hard supply it leaves a fine white mineral film on dark surfaces within days. Two answers exist: a demineralisation cartridge in the tank, which is a consumable with a real working life, or an evaporative build where the minerals stay in the wick. This unit is specified as cartridge optional, recommended wherever the supply is hard.
Which compliance files ship with a quiet humidifier order?
The standard file set is the CE technical file, RoHS and REACH declarations, an EMC test report, the IEC 60335-1 household appliance safety report, and for battery builds a UN38.3 test report with an IEC 62133 cell report and MSDS. For North America we add FCC documentation for the digitally controlled models. Certificates are issued against WL-QH01S, the model code on the order, rather than against a generic family.
Can we sell these under our own brand, with our own packaging?
Yes. Private label covers housing colour, logo placement, retail artwork, manual language and the accessory kit, and most of it sits inside existing tooling for this range, so customisation does not mean re-engineering. The decision we ask buyers to make early is which consumables travel with the appliance, because a unit sold without a cartridge into a hard-water market generates complaints that no artwork will fix.
How often does the unit need cleaning, and what does that involve?
Every five to seven days in continuous use, with a full dry-out if the unit will stand unused. That interval is why we specify a wide tank opening on this chassis: a tank a hand cannot reach into is a tank that never gets cleaned properly. Biofilm in standing water is the underlying reason, and it is not a defect, it is what water at room temperature does.
What warranty and spares support do you provide?
12 months against manufacturing defect on WL-QH01S. Misting discs, wicks, cartridges, seals and cells are stocked as separate line items and can ride in the same container as the units, which is the cheapest way to buy them. We suggest one spare disc per twenty units and one cartridge per unit where the water is hard.
How long does sampling and first production take?
Samples ship in 5 to 7 working days from an existing specification, or 15 to 20 days if a custom colour is required. First production runs in 20-30 days depending on SKU and quantity, measured from order confirmation and deposit, with the exact figure stated on the proforma invoice rather than left open. Battery shipments add a documentation step at booking.
Who This Programme Suits
The programme suits any buyer who has to answer for the product after it is sold, which in practice means everyone except the pure spot trader. A distributor carrying a range needs to know which chassis to put in front of which customer, and the answer is usually decided by water hardness and by who refills the tank.
Hospitality buyers need a fill interval that fits a housekeeping round. Clinical and childcare buyers need a material declaration and a light that can be turned fully off. Facilities buyers need one unit per occupied room rather than one per floor, and they need the reasoning written down so it survives staff turnover.
What all of them have in common is that they are specifying against a room and a routine rather than against a specification sheet, which is why we ask about the site before we quote the unit. For this configuration that means 19.0 mL per hour at 23.2 dB, holding 22.1 hours per fill across a 11 sq m (113 sq ft) room.
How a First Order Is Structured
A first order runs in five steps and none of them need to be slow. The first is the specification: which chassis, which SKU build, and which markets, because the market list decides the documentation. The second is sampling, 5 to 7 working days from an existing specification or 15 to 20 if a custom colour is required.
The third is the paperwork - certificates, manuals, artwork and the battery files where a cell is fitted - and it runs in parallel with the second rather than after it, which is where most of the time is either saved or lost. The fourth is production, measured from order confirmation and deposit. The fifth is booking, which is where a battery build needs its extra few days.
What we ask a buyer to decide before step one is which consumables travel with the appliances, because that choice affects the packing list and the freight, and changing it later costs a second shipment. The WL-QH01S (PRO) packs 48 units to a carton, carries a 12 months warranty and a 20-30 days stated lead time, and draws 2.7 W on the high step.
Next Step for Import Buyers
Two things decide whether this product works, and neither is on the box: whether the tank lasts the interval the site can actually service, and whether the unit can be cleaned inside the time a round allows. Get those two right and the rest of the specification rarely matters.
Everything else on this page exists to make those two decisions possible before money moves - the figures by model rather than by marketing tier, the measurement conditions stated next to the decibel, and the honest statement of where the answer depends on the room.
Enquiries are welcome from anyone supplying this category at volume, whether as an importer, a distributor, a brand owner, a facilities or hospitality group, or a cross-border seller. Samples and the full documentation set are available on request. The WL-QH01S (PRO) packs 48 units to a carton, carries a 12 months warranty and a 20-30 days stated lead time, and draws 2.7 W on the high step.
Published by: Wanlin Manufacturing Group, MistAirHome Export Division
Published on: September 28, 2026
Data sources: in-house factory testing + misting disc and cell specifications + certification and battery files + partner deployment records
Company address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China
References: factory quality manual + third-party test reports + customer shipment records
Contact: Mistairhome@163.com / +8613261677119 / https://www.mistairhome.com